Specifications
1. 500m remote distance 2. 20 channels 3. sequential & salvo fire 4. "test" function 5. time range: 0.1 - 2.0 s
Welcome to choose DBR05-X1/20 remote electronic ignition of fireworks products!
DBR05-X1/20 is a practical small size, a remote controlled electronic ignition of many fireworks products, using 1 million of non-repetition of the more secure codec technology, which allows the set off of fireworks can be tens of meters to a few hundred meters from the set off of wireless remote control, no ignition officers at close range , have the function of a key with 20 groups at the same time set off and a key with 20 group scan be set up the time in chronological order to set off, makes the fireworkssee off of the most convenient, the best results.
Usage:
1. Choose the right remote control lever toggle dial to select the set of points in number, press the launch button on the panel remote control and display the corresponding set of points, and the launch button plus one of automatic functions, the order of discharge only if the repeated manual pressing the launch button.
2. Slide Show to--, choose dial button is pressed together and launch capabilities,
3. Toggle to select the dial shows a group of 1-20 points to any number, press the select dial, display digital flash, this time for the sequential to display numbers in accordance with pre-flash interval set point font size, by group, from small to large ignition sequence (see table next time interval, )Blinking numbers returned again to select the dial set point control mode.
4. Upper left corner of the state of remote controller light is red, green, two colors, can be expressed for each set of points in the state, number of dots under each group had not pressed the launch button when the green, or red, for the arbitrary choice determine the ser of points when the state of discharge.In the volley and the firing order of all the groups after the status indicator is red points(all in green when power on, power off without saving.)
Notes:
1. Do not placed the igniter in the water or in damp places.so as not to affect remote controls distance een damage the igniter.
2. Turn on the power supply of igniter, power supply, lights, press the corresponding figure keys of the remote control, the power lights off, means the group remote control work normal, if press the remote control key long time, the power light flashing, then can judge and test each group of remote control.
3. As far as possible upward extension the receiving antenna to enable remote control receive farthest distance.
4. Normal connecting the ignition herd, testing lights, the can control the ignition,
5. If the igniter does not work, check the battery, if the distance of remote control received shortened, please check the remote controls battery;If the remote control of a certain group can not control the ignition, please reconsider the code (see the notes on igniter).
6. The produce only for the set off of fireworks interval timetable for the order of set off
FiguresKey | Interval (s) | FiguresKey | Interval (s) |
1 | 0.1 | 11 | 1.1 |
2 | 0.2 | 12 | 1.2 |
3 | 0.3 | 13 | 1.3 |
4 | 0.4 | 14 | 1.4 |
5 | 0.5 | 15 | 1.5 |
6 | 0.6 | 16 | 1.6 |
7 | 0.7 | 17 | 1.7 |
8 | 0.8 | 18 | 1.8 |
9 | 0.9 | 19 | 1.9 |
10 | 1.0 | 20 | 2.0 |
Technical parameter
Item | Parameters |
Size (single group) | 9.2cmx6cmx2.5cm |
Remote controller size | 12.5cmx4cmx2.4cm |
Power | AAA (1.5Vx4) |
Power of remote controller | 6F22 (9V) |
Safety testing current | 500M |
