Instruction(3GX Programmable Flybarless System) :
- Brand new redesigned 3GX represents a new generation of multi function flybarless system. The dramatically improved performance will create immediate impact on any enthusiasts.
- 3GX is currently the smallest and lightest flybarless system on the market.Two ports to directly connect Spektrum and JR satellite receivers, along withfull support of Futaba's S-BUS system.
- Based on the 3G FL760 manual setup process, the 3GX can be setup in a few minutesthrough a simple process. In addition, the 3GX can support all of the CCPM swashplatesystem currently on the market including 90, 120, 135, and 140 degrees swashplates.
- Graphical illustrated instruction on the computer setup software directs theuser through a step by step setup process, allowing for quick setups withoutomitting any steps.
- Support Bluetooth connectivity. With the soon to be released Bluetooth connectivitykit, 3GX can be programmed wirelessly from a PC. Eventually there will also besmartphone apps allowing live adjustments to 3GX without powering down.
- With 3GX's built in Align RCE-G600 governor function, no external governor isneeded to reduce electronic wire clutters.
- Custom parameters have been opened up in 3GX to allow pilots to fine tune numeroussettings for swashplate and rudder. Settings export feature allows custom settingsto be shared amongst friends.
- 3GX utilizes brand new gyroscope sensors of the highest specifications whencompared to other flybarless systems currently on the market, allowing it tobe used under harsh conditions. Dual axis plus rudder sensor dramatically improvesswashplate and rudder correction precision compared to last generation 3G. Thisis clearly noticeable in stable hover as well as highly aerobatic routines.
- Suitable for helicopter of all class from 200 to 700, glow engine or electricpowered. The superior vibration resistant characteristic is evident even whenmounted with harder double sided mounting tape.
- 3GX utilizes 16 bit processor which is 4 times faster than previous generation, along with a completely re-written firmware. The result is a dramatic stabilityimprovement from previous generation, with stability that rivals a flybarredhelicopter, yet posses explosive agility.
- With built in pirouette compensation function, 3GX is able to stabilize thehelicopter on a fixed point during pirouetting maneuvers. Pirouetting flips typeof maneuvers are easily accomplished with precision.
- 3GX's rudder allows consistent rudder feel even under high speed conditions. This excellent control feel will allow pilot of all skill levels to experience the perfect integration between 3GX and helicopter.
- Support with APS gyro system and bring up more functions for your helicopter. With the APS gyro, the helicopter will have the ability to self stabilize, hold position as well as altitude, and even autonomous way point flights as well as return home.
Specification(3GX Programmable Flybarless System) :
Operating Temperature:-10~60 degree
X and Y axis Operating Angle Range:-300~+300 degree
Z axis Operating Angle Range:-600~+600 degree
Size:36.5x25.2x15.6 mm Size
Weight11g Weight
Supports Wide/Narrow Bandwidth Digital and brushless servos
Spektrum and JR Satellite antennas support (Replaces original factory receiver)
Futaba S.BUS system support
Built in governor function
Maximum working voltage:8.5V
Compatible with 1024/2048 resolution Spektrum receivers
Supports 90/120/135/140 CCPM swashplates
Field setup without the use of a PC
Compatible with 2 to 5 blades rotor heads
Support up to 6 servos
Automatic servo type recognization
Specification(T-REX 700E DFC) :
Length: 1345mm
Height: 360mm
Width: 208mm
Main Blade Length: 690mm
Main Rotor Diameter: 1562mm
Tail Rotor Diameter: 281mm
Motor Drive Gear:12T
Main Drive Gear:112T
Autorotation Tail Drive Gear: 104T
Tail Drive Gear: 22T
Drive Gear Ratio: 1:9.33:4.37
Weight(With Motor): 2900g
Accessories:
T-REX 700E DFC Kits Set x 1set
Aluminum Tail Boom x 1
3K Carbon Fiber Tail Boom x 1
690 3G Carbon Fiber Blades x 1set
750MX Brushless Motor(530KV) x 1
3GX Flybarless system x 1
DS615 Digital Servo x 3
DS655 Digital Servo x 1
Castle ICE2 HV 120 Brushless ESC x 1
6A External BEC x1
105mm 3K Carbon Fiber Tail Blades x 1set
Radio transmitter and electronic equipment required for assembly:
Transmitter(7-channel or more, helicopter system)
Receiver(7-channel or more)
6S Li-Po 4500 ~ 5200mAh x 2
2S Li-Po 1900 ~ 2300mAh x 1
Dial Pitch Gauge
Specification(T-REX 700E DFC) :
Features:
1. Equipped with the low CG DFC rotor head, effectively reduce wind resistance during flight, providing the most direct and precise control feel back to the pilot, and exhibits exhilarating 3D performance and unimaginable flight speed.
2. Brand new CCPM direct servo linkage design to eliminate the weight of double push-pull linkage system, enabling faster and more precise control reaction.
3. Integrated servo mounts on the main shaft bearing blocks, allowing cyclic servos to be mounted directly onto the bearing blocks, which together with the composite material frame plates, creating a clean and uncluttered look.
4. Utilizes composite carbon material integration technique on frame structure for ease of maintenance and high rigidity. Increased front opening area to allow for simpler battery installation.
5. Innovative sliding battery tray rails imbedded into the 3K side frames, with patented spring loaded latching mechanism, allowing for quick battery access as well as battery protection.
6. Top mounted motor base bringing the motor's center of gravity closer to rotating disc, improving 3D agility and allowing blade drafts to cool the motor effectively .
7. Motor mount consists of third bearing block to provide motor shaft support, effectively reduce torque induced shifts, and minimize gear striping issue.
8. Utilizes high spec MOD1 112T CNC helical main gear and MOD 1 tail drive helical gear to increase gear mesh area, and minimize gear noise during flight.
9. Top mounted ESC platform to take advantage of main blades airflow for effective cooling.
10. New lightweight H-shaped electric device retention system for protection, as well as ergonomically correct design to simplify operation .
11. Equipped with 750MX series high efficiency brushless motor, with ribbed case and fan to dramatically increase cooling effect, and improve overall power output.
12. Brand new gear box with more streamlined design also allows for simpler disassembly.
13. High quality new tail gearbox design, combined with new dual point mounted tail pitch control assembly to minimize slops and increase rudder control precision.
14. High torque rated one way bearing base.
15. High precision bearing supported dual push point rudder control design.
16. High speed rated thrust bearings incorporated into tail blade grips.
17. Equipped with third bearing main shaft support to increase rigidity, meeting the needs of extreme 3D maneuvers.
18. New lightweight landing gears.
19. High grade painted fiberglass canopy with new 4 point anti-vibration mounting mechanism to simplify installation.
20. New CNC aluminum alloy mounting plate.
